- ◎ 无损检测仪器
- 超声波探伤仪 超声波测厚仪 涂镀层测厚仪 磁粉探伤仪 探伤剂 X射线探伤机 粗糙度仪 测振仪 硬度计 防护设备 黑光灯 频闪仪 转速表 观片灯 推拉力计 弹簧试验机 电火花检漏仪 试块|探伤试块 楼板厚度测量仪 裂缝深度测试仪 裂缝宽度测试仪 回弹仪 钢筋保护层测定仪 变形模量测试仪 锈蚀仪 无损探伤配件 相控阵探头 相控阵探伤仪 涡流探伤仪 点焊探头 内窥镜 超声波探头
M201H-RM*价格
阅读： 发布时间：2018-07-21
M201H-RM*|奥林巴斯M201H-RM*延迟块探头|M201H-RM*延迟块探头
M201H-RM*价格|OLYMPUS/M201H-RM*延迟块探头|深圳华清仪器-无损事业部，
探伤仪、探头、连接线、探伤仪电池、探伤仪充电器、耦合剂、试块、合金分析仪、内窥镜等等来电洽谈：
EPOCH 650/EPOCH 6LT/EPOCH 1000/EPOCH 1000i/EPOCH 1000iR/OmniScan SX/OmniScan MX2
27MG /45MG/38DL PLUS/35RDC/Magna-Mike 8600
SONOPEN® Transducers
The Sonopen® transducer has a replaceable delay line that is tapered to a small contact area. This transducer makes reliable thickness measurements in applications such as turbine blades, threads on plastic bottle necks, and tight radii on plastic containers. High-temperature Sonopen delay lines are also available.
|
Frequency |
Nominal |
Transducer |
|||
|
MHz |
Inches |
mm |
Straight |
Right Angle |
45° |
|
15 |
0.125 |
3 |
V260-SM |
V260-RM |
V260-45 |
| Tip Diameter | ||
| Inches | mm | Part Number |
| 0.08 | 2 | DLP-3 |
| 0.06 | 1.5 | DLP-302 |
| 0.08 | 2 | DLP-301* |
*High-temperature delay for use up to 350° F (175° C)
Delay Line Transducers
Microscan delay line transducers provide excellent performance on very thin materials, elevated temperatures, or in applications that require a high degree of thickness resolution.
|
Frequency (MHz) |
Element (inches) |
Diameter (mm) |
Transducer Part Number |
Transducer Part Code |
Holders |
| 0.5 | 1 | 25 | M2008† | U84 | |
| 3 | M207-RB | U8410017 | - | ||
| 5 | 0.5 | 13 | M206-RB | U8410016 | - |
| 5 | 0.25 | 6 | M201-RM | U8410001 | - |
| 5 | 0.25 | 6 | M201H-RM* | U8411030 | 2127 |
| 10 | 0.25 | 6 | M202-RM, M202-SM | U8410003, U8410004 | - |
| 10 | 0.25 | 6 | M202H-RM* | U8507023 | 2127 |
| 10 | 0.125 | 3 | M203-RM, M203-SM | U8410006, U8410007 | - |
| 20 | 0.125 | 3 | M208-RM, M208-SM | U8410019, U8410020 | - |
| 20 | 0.125 | 3 | M208H-RM* | U84100 | |
| 5 | 3 | M2055* | U84 | ||
| V213-BC-RM* | U8411022 | - |
RM = Right Angle Microdot; SM = Straight Microdot; SB = Straight BNC † High Penetration Transducer *Used with Holder, P/C 2133
Replaceable Delay Lines
Standard Delay Lines
Standard delay lines are used in many applications. Special conditions such as high surface temperature, the curvature of the material, or hard-to-access areas may require the use of special delay lines.
|
Element Diameter |
Delay Line Part Number |
Maximum Thickness Measurement Limit* |
||||||
|
Steel Mode 2 |
Steel Mode 3 |
Plastic Mode 2 |
||||||
| Inches | mm | Inches | mm | Inches | mm | Inches | mm | |
| 0.5 | 13 | DLH-2 | 1.0 | 25 | 0.5 | 13 | 0.5 | 13 |
| 0.25 | 6 | DLH-1 | 1.0 | 25 | 0.5 | |||
| DLH-3 | 0.5 | 13 | 0.2 | 5 | 0.2 | 5 | ||
*Exact range depends on material sound velocity, transducer frequency, part geometry, and surface condition.
High-Temperature Delay Lines
High-temperature delay lines function as a protective buffer between the hot surface of the test piece and the transducer's crystal. At elevated temperatures, intermittent contact is recommended to protect the transducer from thermal damage.
|
Element Diameter |
High-Temperature Delays |
|||
|
To 350 °F (175 °C) |
To 500 °F (260 °C) |
To 900 °F (480 °C) |
||
| Inches | mm | |||
| 0.5 | 13 | DLHT-201 | DLHT-2 | DLHT-2G |
| 0.25 | 6 | DLHT-101 | DLHT-1 | DLHT-1G |
| 0.125 | 3 | DLHT-301 | DLHT-3 | DLHT-3G |
单晶探头，用于厚度测量
接触式探头
| 频率 | 晶片直径 | 探头 |
工件编号 |
|
| mm | in. | |||
| 0.5 | 25 | 1.00 | M101-SB* | U8400017 |
| 1.0 | 25 | 1.00 | M102-SB* | U8400018 |
| 1.0 | 13 | 0.5 | M103-SB* | U8400020 |
| 2.25 | 13 | 0.5 | M106-RM | U8400023 |
| M106-SM | U8400025 | |||
| 2.25 | 13 | 0.5 | M1036 | U8400020 |
|
5.0 |
13 | 0.5 | M109-RM | U8400027 |
| M109-SM | U8400028 | |||
| 5.0 | 6 | 0.25 | M110-RM | U8400030 |
| M110-SM M110H-RM** |
U8400031 U8400029 |
|||
| 10 | 6 | 0.25 | M112-RM M112-SM |
U8400034 U8400035 U8400033 |
| M112H-RM** | U8400033 | |||
| 10 | 3 | 0.125 | M1016 | U8400015 |
| 20 | 3 | 0.125 | M116-RM | U8400038 |
| M116-SM | U8400039 | |||
| 20 | 3 | 0.125 | M116H-RM** | U8400037 |
*这些探头只能与高穿透软件选项一起使用。
**需使用弹簧加载支架。
Microscan探头经常与测厚仪、探伤仪及其它超声仪器配合使用，完成多种检测应用。
Microscan探头的工件编号表明了其所使用的接口类型：
RM = 直角Microdot
SM = 平直Microdot
RB = 直角BNC
SB = 平直BNC
SU = 平直UHF
在选择探头时，请查看下面的探头列表，或查阅随您所购买仪器附送的指导手册中的探头频率范围。
45MG
38DL PLUS
2.0 ～ 30 MHz
接触式探头
Microscan接触式探头的一个优点是其通用性；一个单一探头可以覆盖很多工程材料宽泛的厚度范围。接触式探头装有的WC-5防磨板，具有更好的耐用性能和更长的使用寿命。
|
频率 （MHz） |
晶片 （英寸） |
直径 （毫米） |
探头 工件编号 |
探头 订购编号 |
||
| 0.5 | 1 | 25 | M101-SB† | U8400017 | ||
| 1 | 1 | 25 | M102-SB† | U8400018 | ||
| 1 | 0.5 | 13 | M103-SB† | U8400020 | ||
| 2.25 | 0.5 | 13 | M106-RM，M106-SM | U8400023，U8400025 | ||
| 2.25 | 0.5 | 13 | M1036 | U8400019 | ||
| 5 | 0.5 | 13 | M109-RM，M109-SM | U8400027，U8400028 | ||
| 5 | 0.25 | 6 | M110-RM，M110-SM，M110H-RM** | U8400030，U8400031，U8400029 | ||
| 10 | 0.25 | 6 | M112-RM，M112-SM，M112H-RM** | U8400034，U8400035，U8400033 | ||
| 10 | 0.125 | 3 | M1016 | U8400015 | ||
| 20 | 0.125 | 3 | M116-RM，M116-SM | U8400038，U8400039 | ||
| 20 | 0.125 | 3 | M116H-RM* | U8400037 | ||
RM = 直角Microdot；SM = 平直Microdot； SB = 平直BNC
†高穿透性能探头；*使用探头架，工件编号2133；**使用探头架，工件编号2132
| 联系人:张运华 电话:0755-28199550 13684941024 传真:0755-29806349 邮编:518100 地址:深圳市龙华新区三联路清泉二期2栋15A2 网址:http://www.hq1817.com http://hq17.testmart.cn |
